FITTING INSTRUCTIONS FOR TYPE FB-IOO BELT SET

Important Note: Due to the type of belt and the fact that it has not been
fitted by Tollyboy products, it is not possible to provide an anatomically
correct to the wearer pre-shape. However the steel is tempered to render it
easy to manipulate by hand to effect a fitting shape. The steel remains
hardened with no loss of security.

The locking system supplied with belt sets is unique to Tollyboy products, it
offers very high security but is simple in concept. You will find it easy to
use once you become familiar with the system. The first task is to unlock the
waist band, the procedure for this is as follows.

Enter the appropriate key into the lock and turn anti-clockwise whilst
maintaining a light inwards pressure. Continue to turn the key and you will
observe that the lock is unscrewing revealing two anti-turn guide pins.
Unscrew the lock till it disengages completely, approximately 5 to 7 turns
will be required. Make sure you keep the lock parallel on the last two turns
when almost clear of the guide pins, and avoid the tendency for it becoming
cross-threaded.

The wearer should be naked to facilitate fitting, the belt is designed to fit
next to the skin and no attempt should be made to wear it over under garments.
Spring open the waist band just sufficient to slip it on to the waist and
centralise it so that the guard hangs down the back and centrally between the
legs. Close the waist-band by engaging its locking spigot and guide pins; it
will be easier to do this if the wearer stretches her hands above her head in
an attempt to reduce the waist to minimum. 

The waist band should be a snug fit on the waist and be in contact all the way
round. This is where a degree of reshaping may be required but in any case you
will find that it will assume the shape of the waist after a reasonable period
of wear. Make sure the wearer is stood with her legs well apart, swing the
guard up between the legs and engage the e top end with the locking spigot and
guide pins. A word of warning, do not make any attempt to force the joint
together by using the lock's screwing action. If you have difficulty in
getting the waist band and guard to seat correctly, you may that if the wearer
lays flat on her back at this juncture it will alleviate the problem. This
position allows the body mass to settle back into the waist band easing any
pressure at the joint. When you are satisfied that the joint is aligned and
seated correctly you are then ready to fit the lock. You will observe that the
lock has a small flat machined on the outer edge, it is important that the
lock is always fitted with this flat at the top. Locate the lock on to its
guide pins and with the key inserted maintain light inwards pressure, turn the
key clockwise and engage the threaded spigot. Make sure that the lock is
parallel and does not become cross threaded, it should turn easily, if there
is any significant resistance do not force it but start again. Continue to
turn the key clockwise maintaining inwards pressure until the lock is screwed
fully home, this will vary between 5 to 7 turns. Remove the key once the lock
becomes firm enough Do not over tighten it is not necessary and does not
improve the security. Check that the guard is a snug fit and seated correctly,
it is at this juncture that the need for shaping will be apparent to achieve
this. When fitted correctly the labia lips will be forced to protrude through
the vaginal slot and will always be framed by it no matter what position is
adopted.

Experience has shown that the FB/lOO can be worn without any ill effects, some
bruising may occur during the 2 initial period of wear but this will soon
pass. The use of talcum powder is recommended. The wearer will probably
complain of all sorts of problems, but the only valid one is if the skin is
broken and this must be treated seriously. The keyholder should be able to
leave the FB/l OO in place with confidence once fitted correctly.

The FB/IOO will come to no harm if immersed in water, but in practice you will
find that a shower is more convenient than a bath. A detachable showerhead is
ideal for washing out the guard while it is locked in position and negates the
need to release it.

Note Radial locks are designed to operate dry, Do not lubricate with oil.